| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: fix Route Information option length validation
rt6_route_rcv() validates the Route Information option (RFC 4191) length
against the prefix length, but both checks are off by one.
rinfo->length is the ND option length in units of 8 octets and it
*includes* the 8-byte option header, so an option carrying N bytes of
prefix has length == 1 + N/8. RFC 4191 section 2.3 requires length 3
when Prefix Length is greater than 64, and 2 or 3 when it is greater
than 0. The code accepts length >= 2 and length >= 1 respectively.
ipv6_addr_prefix() then copies prefix_len/8 bytes out of rinfo->prefix,
so a Router Advertisement with (prefix_len=128, length=2) or
(prefix_len=64, length=1) makes the kernel read up to 8 bytes past the
end of the option. Those bytes end up in the prefix of the route that
gets installed, so they are visible to userspace:
# RA with a Route Information option (prefix_len=128, length=2)
# followed by a source link-layer address option, 01 01 de ad be ef ca fe
$ ip -6 route show
2001:db8:dead:beef:101:dead:beef:cafe via fe80::1234 dev veth0 proto ra
^^^^^^^^^^^^^^^^^^ the next option, read out of bounds
When the Route Information option is the last one in the packet, those
eight bytes come from the skb tail room instead.
Reject the option lengths RFC 4191 does not allow. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_conntrack_sip: widen NAT rewrite delta to s32 in sip_help_tcp()
sip_help_tcp() stores the size change of each NAT-rewritten SIP message
in s16 diff and accumulates it in s16 tdiff, but a single message can
grow by more than S16_MAX while the packet stays under the 65535
enlarge_skb() limit: nf_nat_sip() rewrites every matching URI, and a long
Contact list expands the message by tens of kilobytes. diff then wraps,
and "datalen = datalen + diff - msglen" yields a huge unsigned datalen,
so the next iteration's ct_sip_get_header() reads past the linearized skb
tail.
Widen diff, tdiff and the seq_adjust hook to s32. Both are bounded by the
65535 byte packet limit, and the seqadj core is already s32
(nf_ct_seqadj_set() takes s32), so no previously accepted input is
rejected.
BUG: KASAN: use-after-free in ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
Read of size 1 at addr ffff888010800000 by task ksoftirqd/1/25
ct_sip_get_header (net/netfilter/nf_conntrack_sip.c:464)
sip_help_tcp (net/netfilter/nf_conntrack_sip.c:1694)
nf_confirm (net/netfilter/nf_conntrack_proto.c:183)
nf_hook_slow (net/netfilter/core.c:619)
ip6_output (net/ipv6/ip6_output.c:246)
ip6_forward (net/ipv6/ip6_output.c:690)
ipv6_rcv (net/ipv6/ip6_input.c:351)
__netif_receive_skb_one_core (net/core/dev.c:6212)
process_backlog (net/core/dev.c:6676)
__napi_poll (net/core/dev.c:7735)
net_rx_action (net/core/dev.c:7955)
handle_softirqs (kernel/softirq.c:622)
run_ksoftirqd (kernel/softirq.c:1076)
... |
| In the Linux kernel, the following vulnerability has been resolved:
keys: fix out-of-bounds read in keyring_get_key_chunk()
For description-level chunks keyring_get_key_chunk() advances the read
pointer by level * sizeof(long) past the inline prefix but only
bounds-checks the prefix, so a long enough key description is read past
its kmemdup(desc, desc_len + 1) allocation. Compute the full byte
offset and bounds-check the description against it before reading.
The walk only reaches a description-level chunk when two keys collide
through the hash, x, type and domain_tag chunks, so this is reached from
an unprivileged add_key(2) with a crafted pair of same-type keys whose
index hashes collide; KASAN reports a slab-out-of-bounds read. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi: Fix stale-data leak into the SCSI sense buffer
iscsi_scsi_cmd_rsp() copies the sense data of a SCSI Response from the
target-supplied data segment. The segment carries a 2-byte sense length
followed by the sense bytes, so it must hold 2 + senselen bytes, but the
bounds check only requires datalen >= senselen:
senselen = get_unaligned_be16(data);
if (datalen < senselen)
goto invalid_datalen;
memcpy(sc->sense_buffer, data + 2,
min_t(uint16_t, senselen, SCSI_SENSE_BUFFERSIZE));
A target that returns a SCSI Response whose datalen equals senselen
(with senselen <= SCSI_SENSE_BUFFERSIZE) makes the memcpy() from data +
2 read up to two bytes past the received data. Those bytes are stale
conn->data contents and end up in the command's sense buffer, which is
returned to userspace.
Account for the 2-byte sense length prefix in the check. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Bound SCSI Response data segment to the connection buffer
iscsi_tcp_hdr_dissect() receives the data segment of several PDU types
into the fixed-size conn->data buffer, which is allocated for
ISCSI_DEF_MAX_RECV_SEG_LEN (8192) bytes. For the LOGIN_RSP, TEXT_RSP,
REJECT and ASYNC_EVENT opcodes the dissect path already rejects a PDU
whose DataSegmentLength exceeds that buffer.
The SCSI Command Response (ISCSI_OP_SCSI_CMD_RSP) path also copies its
data segment (sense/response data) into conn->data via
iscsi_tcp_data_recv_prep(), but it does so without the same check. The
only upstream bound on in.datalen is conn->max_recv_dlength, the
initiator's advertised MaxRecvDataSegmentLength, which is commonly
negotiated well above 8192 (open-iscsi defaults to 262144). A target
that returns a SCSI Response with a DataSegmentLength between 8193 and
max_recv_dlength therefore overflows the 8192-byte conn->data buffer.
Once the same bound applies, ISCSI_OP_SCSI_CMD_RSP is handled exactly
like those responses: bound the data segment, receive it into conn->data
when present, and otherwise complete the PDU with no data. Fold the
opcode into that case group rather than duplicating the check. |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: devicetree: don't free uninitialized dev_name on error path
dt_remember_or_free_map() duplicates dev_name for each map entry. If
kstrdup_const() fails, dt_free_map() frees dev_name in all num_maps
entries, including entries that have not been initialized.
Some pinctrl drivers, including pinctrl-imx, allocate the map with
kmalloc() and leave dev_name for the core to initialize. The untouched
entries therefore contain uninitialized data which is passed to
kfree_const().
Reproduced on qemu's mcimx6ul-evk (pinctrl-imx) with failslab injection
while binding the pinctrl-consuming device, under KASAN:
BUG: KASAN: double-free in dt_free_map+0x34/0xa4
Free of addr c425a900 by task init/1
kfree from dt_free_map+0x34/0xa4
dt_free_map from dt_remember_or_free_map+0x184/0x198
dt_remember_or_free_map from pinctrl_dt_to_map+0x33c/0x4c8
pinctrl_dt_to_map from create_pinctrl+0x9c/0x5c0
Initialize all dev_name fields to NULL before duplicating the device
name, making the full-map cleanup safe after a partial failure. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: x86: Cancel delayed I/O APIC EOI handling before destroying vCPUs
Cancel (and flush) the I/O APIC's delayed EOI handling work during the
"pre VM destroy" phase, before vCPUs are destroyed, as processing the EOI
broadcast will inject another IRQ if the line is asserted, i.e. will try
to deliver an IRQ to the target vCPU(s). Canceling the work after vCPUs
are destroyed leads to UAF if the delayed work is processed after vCPUs are
destroyed.
BUG: KASAN: slab-use-after-free in __kvm_irq_delivery_to_apic_fast+0x9bf/0xa20 arch/x86/kvm/lapic.c:1250
Read of size 8 at addr ffff8880499abea0 by task kworker/1:2/1218
CPU: 1 UID: 0 PID: 1218 Comm: kworker/1:2 Not tainted 7.1.0-rc7 #5 PREEMPT(lazy)
Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: events kvm_ioapic_eoi_inject_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94
dump_stack_lvl+0x100/0x190 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378
print_report+0x139/0x4ad mm/kasan/report.c:482
kasan_report+0xe4/0x1d0 mm/kasan/report.c:595
__kvm_irq_delivery_to_apic_fast+0x9bf/0xa20 arch/x86/kvm/lapic.c:1250
__kvm_irq_delivery_to_apic+0xd8/0xbf0 arch/x86/kvm/lapic.c:1345
kvm_irq_delivery_to_apic arch/x86/kvm/lapic.h:129
ioapic_service+0x308/0x590 arch/x86/kvm/ioapic.c:492
kvm_ioapic_eoi_inject_work+0x13c/0x190 arch/x86/kvm/ioapic.c:532
process_one_work+0xa59/0x19a0 kernel/workqueue.c:3314
process_scheduled_works kernel/workqueue.c:3397
worker_thread+0x5eb/0xe50 kernel/workqueue.c:3478
kthread+0x370/0x450 kernel/kthread.c:436
ret_from_fork+0x72b/0xd30 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
Note, the VM is unreachable once kvm_destroy_vm() starts, and scheduling
new work via kvm_ioapic_send_eoi() can only be done via KVM_RUN, i.e.
requires a live vCPU.
Alternatively, KVM could simply destroy the I/O APIC during the "pre" phase
of VM destruction, but that gets more than a bit sketchy as KVM expects the
I/O APIC to exist if ioapic_in_kernel() is true, and nested virtualization
in particular has a bad habit of touching VM-scope state during vCPU
destruction. E.g. attempting to free the PIC during the pre phase would
lead to a NULL pointer dereference in kvm_cpu_has_extint(), and it's not
hard to imagine the I/O APIC having a similar flaw. |
| In the Linux kernel, the following vulnerability has been resolved:
binfmt_misc: reject a flag character as the field delimiter
The registration string starts with a user chosen delimiter that
separates the individual fields. So that the field parsers terminate
even on a truncated string create_entry() pads the buffer with that
same delimiter:
memset(buf + count, del, 8);
Most fields are scanned for the delimiter with strchr()/scanarg() and
happily stop on the padding. The flags field is different: instead of
scanning for the delimiter check_special_flags() consumes the flag
characters 'P', 'O', 'C' and 'F' and stops at the first byte that is
none of them, relying on the trailing delimiter to end the scan.
If the delimiter is itself a flag character the padding no longer acts
as a terminator. The scan swallows all eight padding bytes and keeps
reading past the end of the allocation until it hits a byte that is
not a flag character. For example registering
PaPEPPxPPiP
with 'P' as the delimiter (name "a", type extension, magic "x",
interpreter "i", empty flags) leaves the flag scan running off the end
of the buffer. The registration is rejected in the end because the
parser does not stop exactly at buf + count, but only after the out of
bounds read has already happened. With an unlucky allocation layout the
scan can walk into an unmapped page; under KASAN it is reported as a
slab out of bounds read. binfmt_misc mounts are available to
unprivileged users in a user namespace so the read is reachable without
privileges.
Reject a delimiter that is one of the flag characters up front. Such a
registration was always rejected anyway, only after the out of bounds
read, so no valid registration string changes meaning. |
| In the Linux kernel, the following vulnerability has been resolved:
veth: convert frag_list skbs before running XDP
A frag_list skb can reach veth with data_len set but nr_frags zero.
veth_convert_skb_to_xdp_buff() only converts skbs that are shared,
locked, have frags[], or do not have enough headroom. It later uses
skb_is_nonlinear() to decide whether to set XDP_FLAGS_HAS_FRAGS and
xdp_frags_size.
That exposes frag_list data to XDP as if it were stored in frags[], but
frags[] is empty. AF_XDP copy mode can then trust the bogus XDP fragment
metadata, walk an empty fragment entry, and crash in memcpy() from
__xsk_rcv().
Route non-linear skbs through skb_pp_cow_data() before exposing them to
XDP, and only advertise XDP frags when the resulting skb has frags[].
skb_copy_bits() already handles frag_list input, and skb_pp_cow_data()
builds frags[] output with skb_add_rx_frag(), which is the
representation XDP multi-buffer expects. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() for transmit path header pulls
In vxlan_xmit(), arp_reduce(), and vxlan_mdb_entry_skb_get(), pskb_may_pull() was
being called to verify the availability of network layer headers (ARP, IPv6/ND,
IP/IPv6 MDB keys).
However, during transmit skb->data points to the MAC header, so skb_network_offset(skb)
is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, len) only checks len bytes from skb->data
rather than skb_network_offset(skb) + len, which can leave part of the network header
in non-linear frags.
Replace these remaining pskb_may_pull() calls with pskb_network_may_pull() to properly
account for the MAC header offset. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() in route_shortcircuit()
route_shortcircuit() currently calls pskb_may_pull(skb, sizeof(struct iphdr))
(or ipv6hdr), which checks if bytes are available starting from skb->data.
However, in vxlan_xmit(), skb->data points to the MAC header, so
skb_network_offset(skb) is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, 20)
only checks 20 bytes from skb->data (which is 14 bytes MAC header + 6 bytes of
IP header), leaving the rest of the IP header potentially un-pulled in non-linear
frags. Subsequent dereferences of ip_hdr(skb)->daddr can read beyond the pulled
linear buffer length.
Fix this by using pskb_network_may_pull(), which adds skb_network_offset(skb) to
the length check to ensure the full network header is present in the linear buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: prevent peer transport count overflow
sctp_assoc_add_peer() increments the association's 16-bit transport_count
for every new unique peer. Adding the 65,536th transport wraps the count to
zero.
SCTP sock_diag uses transport_count to reserve the INET_DIAG_PEERS payload,
then copies one sockaddr_storage for every entry in transport_addr_list.
After the wrap, a diagnostic dump reserves an empty payload and writes
8 MiB of peer addresses past the skb tail.
Reject a new unique peer when transport_count has reached U16_MAX. Perform
the check after the existing-peer lookup so a duplicate address continues
to return its existing transport at the limit. |
| In the Linux kernel, the following vulnerability has been resolved:
can: peak_usb: peak_usb_start(): fix double free of transfer buffer on URB submit error
In peak_usb_start(), each RX URB transfer buffer is allocated with kmalloc()
and the URB is flagged URB_FREE_BUFFER so that the final usb_free_urb() also
frees the transfer buffer.
If usb_submit_urb() fails, the error path frees the buffer explicitly with
kfree(buf) and then calls usb_free_urb(urb). Because URB_FREE_BUFFER is set,
usb_free_urb() -> urb_destroy() frees the same buffer a second time, a double
free of the transfer buffer.
BUG: KASAN: double-free in usb_free_urb.part.0+0x91/0xb0
Free of addr ffff8881069ccb80 by task trigger.sh/285
Call Trace:
kfree+0x113/0x3c0
usb_free_urb.part.0+0x91/0xb0
Drop the redundant kfree(buf); usb_free_urb() already releases the transfer
buffer. This mirrors commit 03819abbeb11 ("net: usb: lan78xx: Fix double free
issue with interrupt buffer allocation"). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: validate DRAW_PRIMITIVES header size before division
vmw_cmd_draw() computes
maxnum = (header->size - sizeof(cmd->body)) / sizeof(*decl);
where header->size is u32 and is taken straight from the user-supplied
command stream. When header->size is less than sizeof(cmd->body) the
unsigned subtraction wraps to nearly 4 GiB, producing a huge maxnum.
Any user-controlled cmd->body.numVertexDecls then passes the bound and
the loop dereferences decl[i] far past the end of the kernel command
bounce buffer, producing an out-of-bounds read of kernel memory.
Reject undersized headers up front. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vmwgfx: bound DMA command body size against suffix pointer
vmw_cmd_dma() locates the DMA suffix at
(unsigned long) &cmd->body + header->size - sizeof(*suffix)
without checking that header->size is large enough to contain both
cmd->body and the suffix. An undersized header makes the suffix
pointer underflow back into the previous command in the bounce
buffer. The verifier later writes suffix->maximumOffset, clobbering
verified fields of an already-relocated earlier command -- a TOCTOU
on the device-visible command stream that lets one command rewrite
another's GMR id, surface id, or other authenticated fields.
Reject the command if the body is too small for the suffix to fit. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: fix wrong pci_get_drvdata type in AER handlers
rtw89 stores an ieee80211_hw pointer via pci_set_drvdata() at probe
time, but io_error_detected() and io_resume() retrieve it as a
net_device pointer. This causes netif_device_detach/attach to
operate on an ieee80211_hw struct, reading and writing at wrong
offsets. The adjacent io_slot_reset() already does it correctly.
Use ieee80211_stop_queues/wake_queues instead, consistent with
every other queue stop/start path in the driver.
Tested on RTL8852CE by calling the handlers from a test module
before and after the fix. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: Correct data type for scan index to avoid infinite loop
A kernel soft lockup was observed during Wi-Fi scanning on the 6GHz band.
The CPU becomes stuck in rtw89_hw_scan_add_chan_ax for over 20 seconds,
leading to a system panic.
RIP points to 0f b6 c3 (movzbl %bl, %eax), which zero-extends
the low 8 bits of RBX into RAX.
RBX (the counter i) has reached a huge value: 0x137466a1.
watchdog: BUG: soft lockup - CPU#2 stuck for 26s! [kworker/u16:4:6124]
Workqueue: events_unbound cfg80211_wiphy_work [cfg80211]
RIP: 0010:rtw89_hw_scan_add_chan_ax+0xb3/0x6e0 [rtw89_core]
Code: a0 48 89 45 a8 44 89 6d 9c 44 89 75 98 eb 29 66 66 2e 0f 1f
84 00 00 00 00 00 66 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 c3 01
<0f> b6 c3 41 3b 44 24 74 0f 83 0b 02 00 00 0f b6 c3 48 8d 14 80 49
RSP: 0018:ffffcb48cbaa39f8 EFLAGS: 00000202
RAX: 0000000000000005 RBX: 00000000137466a1 RCX: 0000000000000000
RDX: ffff89ffc9d851a8 RSI: 0000000000004f0d RDI: 0000000096af0130
RBP: ffffcb48cbaa3a60 R08: 0000000000000000 R09: ffff8a00b7502080
R10: ffff8a00b75ff600 R11: 0000000000000000 R12: ffff89ffc7553870
R13: ffff8a00b7ac8f19 R14: ffff8a00b75020d8 R15: ffff89ffc3d54d80
FS: 0000000000000000(0000) GS:ffff8a014f962000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007558d7f9f4c4 CR3: 0000000178040001 CR4: 00000000001706f0
Call Trace:
<TASK>
rtw89_hw_scan_prep_chan_list_ax+0x8a/0x400 [rtw89_core]
rtw89_hw_scan_start+0x546/0x8a0 [rtw89_core]
? rtw89_fw_h2c_default_cmac_tbl+0x13c/0x1f0 [rtw89_core]
rtw89_ops_hw_scan+0xae/0x120 [rtw89_core]
drv_hw_scan+0xbb/0x180 [mac80211]
__ieee80211_start_scan+0x2fc/0x750 [mac80211]
ieee80211_request_scan+0xe/0x20 [mac80211]
ieee80211_scan+0x123/0x190 [mac80211]
rdev_scan+0x40/0x110 [cfg80211]
cfg80211_scan_6ghz+0x5a1/0xa30 [cfg80211]
By objdump with source:
for (i = 0; i < req->n_6ghz_params; i++) {
5fbc0: 83 c3 01 add $0x1,%ebx --> i++
5fbc3: 0f b6 c3 movzbl %bl,%eax --> get counter
fbc6: 41 3b 44 24 74 cmp 0x74(%r12),%eax
* RBX: 00000000137466a1 -> %bl = a1 -> EAX = 000000a1 (161) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw88: fix OOB read from firmware RX descriptor exceeding DMA buffer
In rtw_pci_rx_napi(), new_len is computed as the sum of pkt_len (14-bit
descriptor field, max 16383) and pkt_offset (drv_info_sz + shift, both
firmware-controlled). The result can exceed RTK_PCI_RX_BUF_SIZE (11478),
causing an out-of-bounds read from the pre-allocated DMA buffer when
skb_put_data copies new_len bytes. The USB transport already validates
this (rtw_usb_rx_data_put checks against RTW_USB_MAX_RECVBUF_SZ); the
PCIe path does not.
Add a check that new_len does not exceed the DMA buffer size. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtw89: add bounds check on firmware mac_id in link lookup
The mac_id field in RX descriptors is 8 bits wide (0-255), but
assoc_link_on_macid[] has only RTW89_MAX_MAC_ID_NUM (128) entries.
While the driver currently assigns mac_id values below 128, the
descriptor value comes from firmware and is not validated before use
as an array index. Add a defensive bounds check in
rtw89_assoc_link_rcu_dereference() to guard against out-of-range
firmware values. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: fix OOB access from firmware tx status queue ID
ath_tx_edma_tasklet() accesses sc->tx.txq[ts.qid] where ts.qid is a
4-bit hardware field (0-15), but the txq array only has
ATH9K_NUM_TX_QUEUES (10) entries. A qid >= 10 causes an OOB array
access.
Add a bounds check on ts.qid before using it as an array index. |
